HMDeviceFirmware

C H A N G E L O G

Please note: Only use the firmware file in connection with the current software-version of the CCUx!

Device: HmIPW-DRBl4 - Homematic IP Wired Blind Actuator - 4 channels

Company: eQ-3, Maiburger Str. 29, 26789 Leer, Germany

Version 1.10.18 - 2023-07-28

** Bugfix

• Configuration parameters cannot be saved

Version 1.10.16 - 2023-06-16

** Improvement

• Execute function "Enable operation within one end position to manually solve any error" only by a long button press

Version 1.10.8 - 2022-11-15

** Bugfix

• Error in slat adjustment, slats move in the wrong direction
• Wrong evaluation of the event counter with multiple links between sensor and actuator

Version 1.10.0 - 2022-06-05

** Bugfix

• Error when the same position is called up several times
• A command triggered by weekprogram is handled by the virtual channels although an error is active

** New Feature

• Add possibilty to increase the time between two slats movements

** Improvement

• Change of driving time while long button press if the end position of the slats is reached
• Enable operation within one end position to manually solve any error
• The time information telegram does not contain a note about the sommer / winter time change.

Version 1.8.4 - 2022-10-19

** Improvement

• General improvements - Code optimisation

Version 1.8.2 - 2021-02-15

** Bugfix

• Section of virtual channels remains in "Move up/down reference run" if all three virtual channels are triggered by Direct Execution Command at startup

Version 1.8.0 - 2021-01-15

** Bugfix

• After a long button press, one channel will sporadically remain permanently supplied with 230 volts.
• After a long keypress the actor runs longer than the set driving time

Version 1.6.0 - 2020-06-26

** Improvement

• Add CHANNEL_OPERATION_MODE to switch between blind and shutter mode

Version 1.4.0 - 2019-09-24

** Bugfix

• Shutters and blinds with longer driving times do not reach end position by short movements (very small values for MAX_TIME_FIRST_DIR)
• If the switch-on and switch-off times in the Easy Profile are set to "Not active" at the same time, the device hangs up.

** Improvement

• Modify event counter check to meet current specification

Version 1.2.10 - 2018-11-07

** Bugfix

• Device doesn't show the supply voltage on display, instead an error is shown

Version 1.2.8 - 2018-11-06

** Bugfix

• Short key press of key visual leads to a restart, if a factory reset was aborted before
• Event counter timeout isn't reset if within the triggered profile the multiexecution flag isn't set

Version 1.2.6 - 2018-09-28

** Bugfix

• Weekprogram sometimes does not trigger all channels

Version 1.2.4 - 2018-08-27

** Bugfix

• If more than one status ACK frame is within the answer queue only the first one is send. Afterwards every new status ACK only triggers the last one
• Statusinfo module creates status ACK telegrams with set ACK, ARR and Boot bits if this is the first status to be sent after startup
• HmIP_APP: Send node confusion when using external send nodes
• Sometimes Statusinfo uses old ApplicationSequenceNumber and Statusinfo with ACK get lost
• Answer-Frames are sometimes sent to the wrong IP destination

Version 1.2.2 - 2018-08-14

** Bugfix

• Real channel does not reach correct final slats position if more than one virtual channel is triggered at same time
• Weekprogram doesn't work correctly if several virtual channels shall be triggered by one switching point

Version 1.2.0 - 2018-08-01

** Bugfix

• configuration of weekprogram channel does not work
• First drive of channel 5, 9 and 13 always takes 90 seconds although the driving time was modified
• Device sends no status info at local operation
• If the link partner is known, an NAK is sent on ("invalid") frames without ARR bit
• If "Disable Message to AC" is activated and only one channel is addressed, no App-Ack is sent.
• Direct Execution Commands without ARR bit are answered at application level
• Homematic IP actuators trigger, due to the astro function, one hour delayed or prematurely on the day of the time changeover.
• Divide maximum number of partners for virtual channels into individual values for virtual A, B and C
• Fix CCM flags according to RFC3610

** Improvement

• All PowerUp parameters, that are listed in list 3 of the device, must be supported.
• Add new parameter for Contrast
• Unify values for undervoltage

--- END OF FILE ---