HMDeviceFirmware

C H A N G E L O G

Please note: Only use the firmware file in connection with the current software-version of the CCUx!

Device: HmIP-ASIR - Homematic IP Indoor Siren

Company: eQ-3, Maiburger Str. 29, 26789 Leer, Germany

Version 1.4.x - 20180627

** Related Hardware

• 1654336D

** Bugfix

• No acoustical and optical signal in case of backup disarm

** Improvement *

** Comments *

Version 1.2.x - 20180212

** Related Hardware

• 1654336D

** Bugfix

• Cyclic StatusInfo contains wrong RSSI-Value.
• App sequecne counter check area
• Trigger of silent alarm does not trigger Status Info to AP

** Improvement

• Removed virtual channels
• Improved StatusInfo and ACK Handling
• Improvements for Security Solution Pro:
  • Added Backup Channel (Channel 2) with parameters for alarmtype, duration, silent alarm and sd-multicast.
  • Added arming of up to seven alarm zones to Direct Execution Command.
  • CSC can be send to Channel 2 with ALARM_MODE bitfield as decision value.
  • Improved sabotage detection: if one or more zones are armed in case of sabotage, the alarm is triggered internally.
  • Added an internal link between Ch 1 and Ch 3 for internal sabotage alarm.
  • Changed Status Info with regard to DeviceSpecific Documenation.
  • Removed PowerUp Parameters from Ch 3.
  • Removed Parameters of ch 1 (sabotage).
  • Added Smoke Detector Multicast in case of acoustic alarm for specific zones.
  • Added silent alarm mode for specific zones.
  • JIRA HMIP_ASIR-48: DISABLE_MSG_TO_AC parameter added

** Comments *

Version 1.0.9 - 201601213

** Related Hardware

• 1654336B
• Had used the R20 resistor in the PCBA to make sabotage button work well.

** Bugfix

• At DEC with duration bigger then 65s the Device execut the duration not correct

** Improvement *

** Comments *

Version 1.0.8 - 201601020

** Related Hardware

• 1654336B
• Had used the R20 resistor in the PCBA to make sabotage button work well.

** Bugfix

• Restart the reciver mode immeditaly in the CB_RX , this bug occur in RC8.

** Improvement *

** Comments *

Version 1.0.7 - 20160921

** Related Hardware

• 1654336B
• Had used the R20 resistor in the PCBA to make sabotage button work well.

** Bugfix

• Delete the LED signal while the sabotage button release or press. For security case.

** Improvement

• Improvement the switch time out for all case.

** Comments *

Version 1.0.6 - 201607027

** Related Hardware

• 1654336B
• Had used the R20 resistor in the PCBA to make sabotage button work well.

** Bugfix

• Corrected the ARR-timeout with sending status-frames.
• Corrected a bug with statusinfo sequence counters.
• If the device is not included the sabotage switch is not working anymore. It also will never retrigger the inclusion process now.

** Improvement *

** Comments *

Version 1.0.5 - 201607025

** Related Hardware

• 1654336B
• Had used the R20 resistor in the PCBA to make sabotage button work well.

** Bugfix

• Added sending of Statusmessges to the linked central if an event from the sabotage button is recognized.
• Removed sending of config update request frames on sabotage button if there is no partner because a statusmessage has been triggered and is enough.
• Statusmessaeges are now send with ARR bit.

** Improvement *

** Comments *

Version 1.0.4 - 201607018

** Related Hardware

• 1654336B
• Had used the R20 resistor in the PCBA to make sabotage button work well.

** Bugfix

• ARR Timeout is ignored
• Fixed the bug of : statusinfo with ARR bit, no timeout. Add timeout for this.

** Improvement

• Changed EMC target. add some predefine in it.

** Comments *

Version 1.0.2 - 201607013

** Related Hardware

• 1654336B
• Had used the R20 resistor in the PCBA to make sabotage button work well.

** Bugfix

• ARR Timeout is ignored

** Improvement

• Delete some unused code and perdefine in the code.

** Comments *

--- END OF FILE ---